4250, 4300 series printer, 4350 series printer, Do-It-Yourself Office, Error Codes, Hewlett Packard Laser Jet 4200, 4300 series printer, Hewlett Packard LaserJet 4240, 4250, 4350 series printer, Hewlett Packard P4014, P4015, P4515 series printers, P4015, P4515 series printers, Paper Jams

HP Laser Jet – Not Picking up Paper / Jamming at feed, Overview and Solution.

Problem: Most Models; Paper Jams / Not picking up paper from tray.

2578481

Error codes: 13.01, 13.30, 13.A2.D2,  13.A3.D3, 13.0000, Misprint.
Error messages you may see on display. (These are different error codes for the same problem on different HP Laser Jet Printers). 

Solution: If you have multiple paper trays, Locate the tray that is having the jamming problem.
Note: Can you use a different tray until the problem is resolved?

Solution Continued: Pull out the paper tray completely from machine.
Remove all paper and discard any damaged paper. Check paper tray size guides and adjust them to correct sizes. Such as 81/2 X 11.

Note: There normally are length and width guides. To adjust them squeeze the blue lever, (Most are Blue not all) until they are set to correct sizes. If the guides are too tight or too loose it can cause jamming /not picking up the paper.
Look for broken guides. If they are broken, you can use packing tape to temporarily keep the guides in place.
Guides

Correct Fanning of Paper:  Fanning the paper introduces static electricity. Instead of fanning the paper, flex the stack by holding it at each end and bringing the ends up forming a U shape. Then, rotate the ends down to reverse the U shape. Next, hold each side of the stack of paper, and repeat this process. This process releases individual sheets without introducing static electricity. Straighten the paper stack against a table before returning it to the tray.

pic

Paper Feed Rollers: It is possible that the Paper Feed Rollers are worn out. You can try cleaning them until new rollers are installed. There are normally three rollers that are used in HP Laser Jet Printers. There is “One in the paper tray” and the other two are inside the machine.
(Located on top of the “Tray Roller” when the tray is closed). You can use 409 or some type of soapy water and a cloth towel. Clean the entire surface of roller then use the dry part of the towel to remove excess.

Rollers

Let me know if this helps or if you need some help, Thanks for Reading!

Izzy

Advertisements
Hewlett Packard Laser Jet 4200, Hewlett Packard LaserJet 4240, Hewlett Packard P4014, P4015, P4515 series printers, Paper Jams

Testing Paper Feed Solenoids.

Many people who repair their own HP printers change the feed rollers and continue getting jams and decide to call it quits at that point.  They cant understand why it’s still jamming.   The problem more than likely is the Paper Feed Solenoids.  Look in the event log.  You will see 13.98, 13.02, 13.03 errors if the solenoids are having issues.

It’s a hassle to have to pull all the covers off just to see if the paper feed solenoid needs to be replaced.  Here’s a way to test them so you don’t have to.  This test applies to  Hewlett Packard Laser Jets 4200, 4300, 4240, 4250, 4350, P4014,  P4015,  P4515 and many others.

Go into “Diagnostics” and “Paper Path” Test Mode.
Set it for 10 prints, single sided and select the tray that you would like to test.
Pay close attention  to the sound, speed and rhythm of the machines operation.
If the solenoid is good you will hear the same rhythm and operation through out the test.  But,  if there is an issue with the solenoid you will notice a pause.   It will “hiccup” and pause just for a moment, then continue.  If it is really bad, it may end up jamming or become obvious that the foam is totally destroyed.
You will become acquainted with this and be able to quickly tell if there is a problem.  If you don’t do it that often you may have to pull the solenoids off to test them.  It’s very subtle but if you do it enough you’ll be able to spot it right off.

Look at the following Video below. I am testing tray 2 and tray 3 on a Hewlett Packard Laser Jet 4250.  First is tray 2 with no problem ( Just Changed it) and next is tray 3 with an obvious problem with the solenoid.

Remove the Solenoid and do a visual inspection.

See Video Below

Replaced the bad solenoid with a “New Solenoid  RK2-0269”.

Hewlett Packard Laser Jet 4200, 4300 series printer, Hewlett Packard LaserJet 4240, 4250, 4350 series printer, Hewlett Packard P4014, P4015, P4515 series printers, P4515 series printers

No power on Hewlett Packard LaserJet’s 4200, 4300, 4240, 4250, 4350, P4010 and P4510 printer series Printers


No power on Hewlett Packard LaserJet’s 4200, 4300, 4240, 4250, 4350, P4010 and P4510 printer series  Printers

Check the power cord at the wall outlet and test for power. If good, check the connection on the machine side of power cord. The following is for printers with duplexers. If it doesn’t have a duplexer see the second illustration and push the power cord into machine.

Duplex 2

Next, Pull Duplexer halfway out of printer. Push the power cord into machine as far as it can go to make sure there is a good connection.

Duplex 1

If this is good you will need a Power Supply assembly.

Hewlett Packard Color Laser Jet Pro M451 series printer, Hewlett Packard Laser Jet P3015 series printer, Hewlett Packard P4014, P4015, P4515 series printers, Service Guides

HP-Service Manuals